Ilgner, H2018-05-152018-05-152017-09Ilgner, H. 2017. Non-invasive detection of sedimentation and its removal in industrial pipeline. 18th International Conference on Transport and Sedimentation of Solid Particles, 11-15 September 2017, Institute of Hydrodynamics, Czech Academy of Sciences, Prague, Czech Republic, pp 121-126.http://149.156.33.48/~loczek/papers/20170911-15-T&S_18_Contents.pdfhttp://hdl.handle.net/10204/10211Copyright: 2017 Wroclaw University of Environmental and Life Sciences. Due to copyright restrictions, the attached PDF file only contains the abstract of the full text item. For access to the full text item, kindly consult the publisher's website.The paper describes the extensive field evaluations of the “Settled Bed Detector” on different mine sites over a 12-month period. Applications range from cemented backfill, a well-graded magnetite product, coarse phosphate tailings and a fine cyclone overflow stream gravitating down a partially filled pipe. Even though it was evident that stationary beds occurred repeatedly whenever process conditions became unfavourable, this did not pose an immediate risk towards blockages. In most cases, the beds were rapidly depleted as soon as either the flow rate was increased, or when the slurry relative density was changed. In other instances, stationary beds remained in the pipeline during extended shut-down periods, which posed a serious risk for cemented backfill operations. Where typical flow rate fluctuations regularly produce and soon thereafter remove small beds, it is undesirable to raise an alarm each time bed develops. In order to only trigger meaningful alarms, additional sensors had to be placed strategically on the side of the pipeline to detect the actual bed height. This configuration proved to be successful, that the next generation of the instrument is in the process of being developed with multiple sensors along the pipe circumference to accurately determine the horizontal interface level between the stationary bed and the flow above it. With a few instruments along the entire pipe route, this new configuration also enables thr tracking of moving dune formations, or the deliberate operation of a pipeline with a controlled stationary bed to reduce abrasive wear at the pipe invent.enStationary bedsAlarm triggersSedimentationSolid particlesConference PresentationIlgner, H. (2017). Non-invasive detection of sedimentation and its removal in industrial pipeline. Wroclaw University of Environmental and Life Sciences. http://hdl.handle.net/10204/10211Ilgner, H. "Non-invasive detection of sedimentation and its removal in industrial pipeline." (2017): http://hdl.handle.net/10204/10211Ilgner H, Non-invasive detection of sedimentation and its removal in industrial pipeline; Wroclaw University of Environmental and Life Sciences; 2017. http://hdl.handle.net/10204/10211 .TY - Conference Presentation AU - Ilgner, H AB - The paper describes the extensive field evaluations of the “Settled Bed Detector” on different mine sites over a 12-month period. Applications range from cemented backfill, a well-graded magnetite product, coarse phosphate tailings and a fine cyclone overflow stream gravitating down a partially filled pipe. Even though it was evident that stationary beds occurred repeatedly whenever process conditions became unfavourable, this did not pose an immediate risk towards blockages. In most cases, the beds were rapidly depleted as soon as either the flow rate was increased, or when the slurry relative density was changed. In other instances, stationary beds remained in the pipeline during extended shut-down periods, which posed a serious risk for cemented backfill operations. Where typical flow rate fluctuations regularly produce and soon thereafter remove small beds, it is undesirable to raise an alarm each time bed develops. In order to only trigger meaningful alarms, additional sensors had to be placed strategically on the side of the pipeline to detect the actual bed height. This configuration proved to be successful, that the next generation of the instrument is in the process of being developed with multiple sensors along the pipe circumference to accurately determine the horizontal interface level between the stationary bed and the flow above it. With a few instruments along the entire pipe route, this new configuration also enables thr tracking of moving dune formations, or the deliberate operation of a pipeline with a controlled stationary bed to reduce abrasive wear at the pipe invent. DA - 2017-09 DB - ResearchSpace DP - CSIR KW - Stationary beds KW - Alarm triggers KW - Sedimentation KW - Solid particles LK - https://researchspace.csir.co.za PY - 2017 T1 - Non-invasive detection of sedimentation and its removal in industrial pipeline TI - Non-invasive detection of sedimentation and its removal in industrial pipeline UR - http://hdl.handle.net/10204/10211 ER -